TiipeOf Tu'ameaCmautuButtonsAnd SomeTips

Ituaiga o faamau tungsten carbide e:

1.Fa'amau Fa'alilo

Fa'amau fa'apolofesa mo le fa'atūina o samala ma'a, DTH ma fa'amau fa'avili mo mea fa'asu'u'u i fau ma'a malosi.

2.Fa'amau fa'amau o Carbide

Fa'amau fa'amau mo le fa'aofiina o samala vili ma'a, pa'u DTH ma fasi fa'a'oloa, e fetaui lelei mo fa'ama'a ma'a.

3. Fa'amau pulu

Fa'amau pulu mo le fa'aofiina o le DTH ma fa'amau fa'apipi'i, e talafeagai mo fa'ama'a ma'a.

O nifo mafolafola pito i luga, e talafeagai mo vili pupuni, fasi taimane, fa'amautu pu, ma isi, fa'aitiitia le ofuina o le sila.

4. faamau foliga sipuni

Fa'amau fa'atusa sipunimo le fa'aofiina o mea fa'apipi'i mo le vili saosaoa i ma'a vaivai.

5.Wedge Buttons

Fa'amau fa'atusa, fa'aoga mo le fa'aofiina o pa'u DTH fa'apitoa fa'apena ma pa'u ta'avale, e talafeagai mo fa'ama'a vaivai ma ROP maualuga ma nifo gau maualalo.

O le faʻamau faʻamaufaʻailoga sima o loʻo taʻua i luga o foliga eseese o loʻo i ai a latou vaega faʻaoga ma uiga galue. O le a le ituaiga faʻamau faʻamaʻi faʻamaʻi e tatau ona faʻaaogaina e faʻatatau i le suʻega ma filifili le foliga faʻamau faʻamaʻi talafeagai e tusa ai ma le tulaga moni.

Fa'aoga talafeagai o fa'amau carbide

I le faʻagasologa o le faʻaogaina tatau o faʻamau carbide sima, o mea nei e tatau ona gauai atu i ai:

1. Don't treat it casually because of wear resistance. Any drill bit needs to monitor its use at any time. Once abnormality is found, if it is repaired in time, the carbide button drill bit is no exception. We must always pay attention to whether it has "cracking" phenomenon or peeling. When this happens, it means that the wear of the drill affects its use, and it needs to be repaired. When the rock drilling speed of the rock drill drops significantly, we should also consider that it may be due to excessive wear of the drill.

2. E le tatau ona faʻaaogaina le malosi faʻamalosi i le taimi o le taotoga. E tatau ona fa'aitiitia le malosi o le fa'aoso e fa'aitiitia ai le mamafa o le vili fa'amau carbide. I le taimi lava e tasi, e tatau ona faʻaaogaina se aofaiga tele o le vai mo le sasaina e aveese ai mea leaga na gaosia i le taimi o le taotoga. E tatau foi ona gauai atu i le faʻaogaina o le vai faʻafefe, e tatau ona amata le faʻafefeteina o le vai, ma e tatau ona vave amata le fufuluina pe a naʻo le galue, a leai o le a mafua ai le maualuga o le vevela o le meafaigaluega vili ma faʻafuaseʻi ona fetaiaʻi ma vai e malulu ma mafua ai ma'e.

O le ZZBETTER o loʻo i ai se faʻasologa atoatoa o nifo sima carbide polo, ma o lapoʻa eseese o faʻamau faʻamaina carbide e mafai ona gaosia ma faʻapitoa.